Your cart is empty
To keep your Colt Single Action Revolver in top shape, you'll need to know how best to care for it. This gun, a piece of history and craftsmanship, asks for special cleaning attention. As a firearm owner, it is crucial to prioritize the proper care and maintenance of your weapon.
A clean and well-maintained gun ensures its accuracy and reduces instances of misfire, increasing its longevity in the long run. Thus, we have outlined an efficient guide on effectively cleaning a single-action revolver using essential tools and techniques. By following these steps diligently, you can ensure that your firearm remains in optimal condition for as long as possible.
To deep clean your Colt Single Action Revolver, start by taking it apart. First, remove the cylinder to access hard-to-reach spots where dirt builds up. Use a small brush to clean these areas well.
Pay special attention to the barrel and chamber; they get dirty fast from shooting. A soft cloth helps wipe down each part gently but thoroughly. Next, check the springs and pins inside for any signs of wear or damage.
If you find issues here, it's best to replace those parts soon to keep your gun working right. Finally, make sure all metal surfaces are free of fingerprints and moisture before putting everything back together.
To pick the right supplies for cleaning your gun, start with basics like Q-tips. They reach hard-to-clean spots. Safety is key before anything else.
Always check that your gun isn't loaded by carefully checking the chambers of your revolver. Keep any bullets far from your work; another room works best. When ready to clean, take apart what's needed, but don't go too deep unless you know how because it can hurt the small parts of your gun.
Clean starting with the barrel as most dirt builds up there. For a dirty barrel, let some solvent sit in it before wiping, or use a mop soaked in solvent and push through until its inside comes out clean. Do this in every chamber, too. Areas with tough stains, like the back of the cylinder, might need soaking and brushing.
Then, oil the points touching metal together using a little so much that they shine but aren't slippery. After all these steps, pull every piece back together.
Proper lube is a must for your Colt Single Action Revolver. Use synthetic oils only. They don't get hard or gummy over time like some others.
A good choice is Clenzoil for regular care between serious cleanings. Just one drop at every bearing spot does the trick. For semi-autos, spread one drop along the barrel, too.
Important areas are the gas ring and ratchet on revolvers; they need oil to soften recoil's hit when you shoot—a cushion that helps keep your gun working longer without wear and tear. Remember not to let it run dry; a tiny bit of #2 synthetic grease works well on moving parts like bushing fronts, rear ratchets, and base pins, keeping everything running smooth. Stay clear from 3 1 oil, though—it may creep into tight spots but ends up causing more trouble by gumming up inside.
After cleaning your Colt Single Action Revolver, putting it back together is next. Start by fitting the internal pieces just right. Make sure each part snaps into its place smoothly.
Put the cylinder back in and check that it spins free when you turn it with your hand. Next, replace the barrel carefully to avoid any damage. Once reassembled, do a function test to ensure everything works as it should.
Cock the hammer; make sure it locks well at full cock and half-cock positions too. Pressing the trigger should cleanly release the hammer each time without fail. Also important is always to point the gun safely while checking that its parts move okay after putting them together again.
Remember safety rules, like using the correct bullets for this gun, to keep shooting safe from harm or the revolver's breakdown. Keep practicing handling safely, especially if you're new or have been away from using guns for a while. This helps keep skills sharp and makes single-action revolvers more fun and safer to use.
When you store your Colt Single Action, keep it in a cool, dry place. Moisture is bad for the metal and can lead to rust. Use a gun safe or cabinet with good airflow to avoid dampness.
A silica gel pack inside will help absorb moisture from the air, keeping your revolver drier. Make sure the storage spot doesn't get too hot or cold, as big temperature changes can also harm your gun over time. Don't wrap it tightly in cloth, as this can trap moisture close to its surface; instead, use a breathable gun sock that lets air move around.
For extra care, lightly oil parts of the revolver before storing it long-term, but don't put on too much—just enough for protection without attracting dirt. Remember these steps every time you put away your piece after cleaning: they ensure longevity and reliability when stored correctly over years of ownership.
When looking online for Colt revolvers for sale, focus on trusted sellers like Ron's Guns. Check their history and reviews from other buyers to ensure they're reliable. Ensure the Colt has all the documents proving it's legal and authentic.
Ask about its past use and maintenance record, too. This information can help you understand how well the gun was cared for before. It's key to see if any parts were changed or fixed over time.
Understanding these details helps find a good piece that will last long without big issues. Also, think about joining online forums where gun fans talk. People often share leads on good buys or sell their own guns when upgrading or changing collections.
Lastly, be ready to pay more for a high-quality Colt, as lower prices might mean hidden problems with the revolver. Remember this advice during your search.
194 Boston Post Rd.
East Lyme, CT 06333